Install new PBS array. Removal of Iris Unit 1. Adjust each item according to the table below. Connect the service kit extension cables. G Reflector Adjustment 1. Loosen the 1 screw fixing the mirror adjusting lever A just until the lever can be shifted. Adjust the mirror adjusting lever A position to minimize color unevenness on the screen by shifting the lever in arrow directions. Operating Procedure 1. Run software program by the keyboard entry.
Adjustment Tool [AE] 2. The first menu is Port selection menu. Adjust the projector by selecting the necessary item from the menu in each stage. Data Setting Menu 7. Explanation of Buttons Micom Data [Transmission]: Reads the microcomputer data from the file and transmits it to the projector.
Micom Data [Reception]: Receives the microcomputer data from the projector and writes it in the file. Receiving and transmitting of the data Click a target button and specify a file name. Adjustment Menu 7. The 8 and 2 keys on the keyboard have the same functions. If releasing the mouse or key after pressing it continuously, the data is transmitted once. Click the OK button. Board is replaced and the product serial number disappears. When "Revision of filter sensor" window is displayed and the window will close automatically in approx.
Board P. Board H-P. Board S-P. Board R-P. Board V-P. Page A-P. Board, K2-P. Panasonic lcd projector operating instructions model no. Lcd home cinema projector pt-aeu operating manual 27 pages.
Page 2: Important Safety Notice We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector.
The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required. Page 5 Settings Menu Navigation Do not continue to use the projector in such cases, otherwise fire or electric shocks could result.
Check that no more smoke is coming out, and then contact an Authorized Service Center for repairs. Page 7: Cautions Do not touch the leaked liquid from the batteries.
If you touch the leaked liquid, it may hurt your skin. Immediately wash away the liquid with water and seek medical advice. If you get the leaked liquid in your eye, it may cause blindness or damage. Page 8: Cautions When Transporting Precautions with regard to safety Do not short-circuit, heat or disassemble the batteries or place them into water or fire.
Failure to observe this may cause the batteries to overheat, leak, explode or catch fire, and burns or other injury may result. Page 9: Cautions When Installing Cautions when installing Avoid setting up in places which are subject to vibration or shocks. The internal parts can be damaged, which may cause malfunctions or accidents. Avoid setting up in places which are subject to sudden temperature changes, such as near an air conditioner or lighting equipment.
Page Accessories Precautions with regard to safety Accessories Make sure the following accessories are provided with your projector. Projection lens Lens cover Protects the projection lens from dust or dirt. Page 13 Back and bottom view Security lock Attach the commercial shackle lock Air intake port which is provided with the projector. Page Setting Up Setting up Screen size and throw distance You can adjust the projection size with 2.
Calculate and define the throw distance as follows. Projected image Shown as size All measurements and the calculation results bellow are approximate and may differ from the actual measurements.
Page Lens Shift And Positioning Setting up Lens shift and positioning If the projector is not positioned right in front of the center of the screen, you can adjust the projected image position by moving the lens shift dials within the shift range of the lens. Page 17 Projector location range You can determine where to locate the screen and the projector by considering the lens shift possibilities.
Page Connections Connections Before connecting to the projector Read and follow the operating and connecting instructions of each peripheral device. The peripheral devices must be turned off. Use cables that match each peripheral device to be connected. Confirm the type of video signals. Audio cables must be connected from each peripheral device directly to the audio reproduction system.
Ask your dealer about the replacement of the lamp unit and check the inside of the projector. Ask an Authorized Service Center to clean inside the projector at least once a year. If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation. It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your nearest Authorized Service Center to clean the projector when required. Please discuss with the Authorized Service Center regarding cleaning costs.
We are constantly making efforts to preserve and maintain a clean environment. Please take non repairable units back to your dealer or a recycling company. The projector lens needs to be handled with care. Cover the lens with the lens cover when transporting the projector. Do not hold the front leg adjusters or the top cover to move the projector, as this may damage the projector. Avoid setting up in places which are subject to sudden temperature changes, such as near an air conditioner or lighting equipment.
The life of the lamp may be shortened or the projector may be turned off. If installing the projector to the ceiling, ask a qualified technician or an Authorized Service Center to carry out all installation work. You will need to purchase the separate installation kit Model No.
Furthermore, all installation work should only be carried out by a qualified technician. Failure to observe this may result in malfunctions or the life of the lamp or the other components may be shortened. Draw curtains or blinds over any windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen. If the surface of the lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen.
Moreover, when not using the projector, attach the lens cover. Do not project the same image for long periods of time, as this may remain as an afterimage on the liquid crystal panel.
Display the white screen test pattern for more than an hour to remove it. The liquid crystal panel of the projector is built with very high precision technology to provide fine picture details.
Occasionally, a few stuck pixels may appear on the screen as fixed points of blue, green or red. It is recommended to switch off the projector once and try after 1 hour later again.
Please note that this does not affect the performance of your LCD. The projector has a high pressure mercury lamp and that is characterized as follows. The lamp may explode if using the projector after the instructed lamp replacement timing. The lamp life depends on individual lamp characteristics, usage condition and the installation environment. Especially the consecutive use of the projector for more than 10 hours, or the frequent switching on or off may greatly affect on the lamp life.
If you use the projector consecutively 6 hours every day, the optical components may need to be replaced in less than 1 year. When any button is pressed, the button backlight is lit.
Without any operation, it gets darker after 5 seconds and goes off after next 5 seconds. Press the tab and lift up the cover. Insert the batteries according to the polarity diagram indicated inside. Contact an Authorized Service Center for repairs. Connect a compatible cable for controlling the projector remotely via your computer.
You can adjust the projection size with 2. Calculate and define the throw distance as follows. Started Getting. All measurements and the calculation results bellow are approximate and may differ from the actual measurements. Close window shades or curtains to block the lights. You can use the projector with any of the following 4 projection methods. Getting Started. Do not touch the air exhaust port directly. If the projector is not positioned right in front of the center of the screen, you can adjust the projected image position by moving the lens shift dials within the shift range of the lens.
You can determine where to locate the screen and the projector by considering the lens shift possibilities. Turning the dials maximum limit is 4 or 5 times from the default position. Read and follow the operating and connecting instructions of each peripheral device. The peripheral devices must be turned off.
Audio cables must be connected from each peripheral device directly to the audio reproduction system. Welcome to ManualMachine.
We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. PT-AEU Before operating this product, please read the instructions carefully and save this manual for future use. Important Information. Important Safety Notice Dear Panasonic Customer: The following information should be read and understood as it provides details, which will enable you to operate the projector in a manner which is both safe to you and your environment, and conforms to legal requirements regarding the use of projectors.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna.
Information Important. Quick steps 1. Important Information Important Safety Notice Settings Menu Navigation Do not attempt to repair the projector yourself, as this can be dangerous. Do not use other than an authorized ceiling mount bracket. Unplug the power plug from the wall outlet immediately when problem occurred.
Do not overload the wall outlet. Never attempt to modify or disassemble the projector. Clean the power plug regularly to prevent it from becoming covered in dust. Do not handle the power plug with wet hands. Failure to observe this may result in electric shocks. Insert the power plug securely into the wall outlet. Do not use damaged plugs or loose wall outlet.
Do not place the projector on top of surfaces which are unstable. Do not place the projector into water or let it become wet. Failure to observe this may result in fire or electric shocks. Do not do anything that might damage the power cord or the power plug.
Do not place the projector on soft materials such as carpets or sponge mats. Do not place liquid containers on top of the projector. If any water gets inside the projector, contact an Authorized Service Center.
Do not insert any foreign objects into the projector. Store the batteries in a plastic bag and keep them away from metallic objects. Precautions with regard to safety. Do not touch the leaked liquid from the batteries. During a thunderstorm, do not touch the projector or the cable. Electric shocks can result. Do not use the projector in a bath or shower. Fire or electric shocks can result. Do not place your skin into the light beam while the projector is being used.
Do not look into the lens while the projector is being used. Do not place your hands or other objects close to the air exhaust port. Do not place your hands or face, or objects which cannot withstand heat close to this port [allow at least 50 cm 20" of space], otherwise burns or damage could result. The lamp cover gets very hot, and touching it can cause burns. Electric shocks or explosions can result if this is not done. Do not allow infants or pets to touch the remote control unit.
Do not cover the air intake port or the air exhaust port.
0コメント